产品分类

应用 Applications

这种类型的设备，适应的物料比较多，除基本型提及的物料外，还有:安眠酮.A.B.C中间体、A.B.S树脂、A.S.C、 白碳黑、苯茶毗酮、茶粕、草酸催化剂、促进剂m、d.m、触媒、沉淀炭粉、对乙酷氮基苯磺酷氨、对氨基水杨酸、哆耳玛托、对苯二酸、二乙苯按、二氧花、活性碳、氟硅酸钠、 氟石矿、副产硫按、硅胶粉末、合成树脂、磺酸钙、 聚丙烯树脂、金霉素、焦硅酸钠、糠氯酸咖啡渣、口服葡萄糖、硫酸钠、硫化矿、磷矿粉、兰BB、P.V.C、熔融磷肥、 四环素、三氧化铁、碳酸钙、钦铁矿、铜矿、土豆粉、尾煤、硬脂酸盐、玉米蛋白、药品、药剂、氧化铁、酒渣等。

This type of equipment is suitable for many materials, except those mentioned in the basictype. Also: methaqualone, A.B.C intermediate, A.B.S resin, AS.C, white carbon blackbenzene-tea pyrazolone, tea meal, oxalic acid catalyst, accelerant m, d.m, catalyst.precipitated carbon powder,p-acetylazobenzene sulfony ammonia, p-aminosalicylic acidtolmetol, p-phenylene diacid, diethylbenzene ammonium, titanium dioxide, activated carbon.sodium fluosilicate, fluorspar ore, byproduct ammonium sulfate, silica gel powder, syntheticresin, calcium sulfonate, polypropylene resin, aureomycin, Sodium pyrosilicate, bran chloricacid coffee residue, oral glucose, sodium sulfate, sulfide ore, phosphate rock powder, blueBB, PV.C. molten phosphate fertilizer, tetracvcline, ferric oxide, calcium carbonate, ilmenitecopper ore, potato powder, tail coal, stearate, zein, drugs, pharmaceuticals, iron oxide, wineresidue,etc.

原理 Principles

具有分散作用的风机，特别适合热敏性物料的气流干燥作业。高速飞旋的风机叶轮，能把湿的、甚至结块的物料解碎，直至分散，在分散过程中同时搅拌、混合，然后物料和热气流平行地流动。这种类型的设备，适应干燥滤饼结块的，但还属于表面水份的物料，含湿量≤40%，如果处理量大或者成品要求干至15%以下时，可采用二级气流干燥。当物料含湿量超过40%，但<60%时，进料较困难，应采用混料器，通过混进干料的方法以降低进料水份，此时，干燥设备的总产量就有较大幅度的下降，这在经济上是不合算的。因此，用户应先用机械的方法(离心脱水或压滤)尽可能的降低进料水份，以确保干燥作业上的顺利进行。

Fan with dispersing function is especially suitable for airflow drying of heat sensitivematerials.The high-speed whirling fan impellercan break up wet or even cakedmaterials until they are dispersed,stir and mix atthe sametime during the dispersionprocess, and then the materials and hot air flow in parallel.This type of equipment issuitable for drving materials with caked filter cakes, but also with surface moisturecontent less than or equal to 40%. if the treatment capacity is large or the finishedproduct requires drying below 15%, secondary air flow drying can be adopted. Whenthe moisture content of the material exceeds 40%, but is less than or equal to 60%, itis more difficult to feed. A mixer should be used to reduce the moisture content of thefeed by mixing dry materials. At this time. the total outout of the drving eauipment wll be greatly reduced, which is uneconomical, Thereforeusers should first use mechanical methods (centrifugal dehydration or pressure flktration) to reduce the feed water as much as possible toensure the smooth progress of drving operations.

技术参数 Technicalparameters

干燥实例 Dried samples